站点设定

仓库
语言设定
货币设定
资源
视频库
Cx Family Common Mode Chokes
0402CT Low Profile Chip Inductors
XAL7050 High-inductance Shielded Power Inductors
XGL4020 Ultra-low DCR Power Inductors

LPD6235 Series

Common Mode Chokes

符合RoHS 无卤素 AEC-Q flag
Coilcraft LPD6235 Series provides both common mode and differential mode filtering in a single low-profile miniature device. They provide 100 Vrms, one minute winding-to-winding isolation.
  • Low-profile miniature CM choke measures only 3.5 mm high, 6.2 mm square
  • Common- and differential-mode filtering in a single device
  • Up to 130 MHz differential mode cutoff frequency
  • AEC-Q200 Grade 1 (–40°C to +125°C)
Refer to Designing Common Mode Filters for design guidance.
立即购买:
计数 单价
1 $1.59
350 $1.37
700 $0.83
1400 $0.64
2800 $0.56
5000 $0.51

对于大批量采购或非库存产品,点击这里请求报价

. 现货,可今天发货.
索取样品:

规格

Electrical specifications at 25°C.

零件号 1 线组数 共模
峰值阻抗 (kΩ)
截止
频率 (MHz) 2
最小
电感 (µH) 3
Irms (A) 4 DCR max (Ω) 5 隔离
电压 (Vrms) 6
LPD6235-682MR_ 2 8.52 @ 39.0 MHz 130 5.4 1.40 0.120 100
LPD6235-103MR_ 2 11.67 @ 28.0 MHz 110 8.0 1.30 0.157 100
LPD6235-223MR_ 2 22.75 @ 19.0 MHz 52.0 18 0.85 0.300 100
LPD6235-473MR_ 2 34.39 @ 12.0 MHz 48.0 38 0.60 0.620 100
LPD6235-104MR_ 2 59.92 @ 8.7 MHz 34.0 80 0.40 1.200 100
LPD6235-474MR_ 2 178.15 @ 3.5 MHz 20.0 376 0.25 3.500 100
LPD6235-105MR_ 2 240.93 @ 2.4 MHz 9.8 800 0.15 7.000 100
LPD6235-155MR_ 2 357.53 @ 1.8 MHz 6.1 1200 0.14 10.800 100
LPD6235-205MR_ 2 574.18 @ 1.5 MHz 4.5 1600 0.11 16.000 100
注释
  1. When ordering, please specify termination and packaging codes: e.g. LPD6235-205MRC
  2. Frequency at which the differential mode attenuation equals 3 dB
  3. Inductance shown for each winding, measured at 100 kHz, 0.1 Vrms, 0 Adc on an Agilent/HP 4284A LCR meter or equivalent.
  4. Irms: Current that causes a 40°C temperature rise from 25°C ambient. This information is for reference only and does not represent absolute maximum ratings.
  5. DCR is for each winding, measured at 25°C. For other operating temperatures, use this DCR at Temperature calculator.
  6. Interwinding isolation (hipot) tested for one minute.

 

端子:

  • R = Matte tin over nickel over silver.
  • Q = RoHS tin-silver-copper (95.5/4/0.5)(Special order, added cost)
  • P = non-RoHS tin-lead (63/37)(Special order, added cost)

包装:

  • C = 7″ machine-ready reel. EIA-481 embossed plastic tape (350 parts per full reel). Quantities less than full reel available: in tape (not machine ready) or with leader and trailer ($25 charge).
  • B = Less than full reel. In an effort to simplify our part numbering system, Coilcraft is eliminating the need for multiple packaging codes. When ordering, simply change the last letter of your part number from B to C.
  • D = 13″ machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked (1500 parts per full reel). Quantities less than full reel available: in tape (not machine ready) or with leader and trailer ($25 charge).
环境
环境:
符合RoHS , 无卤素
环境温度范围:
–40°C to +125°C with (40°C rise) Irms current
储存温度范围:
Component: –40°C to +165°C
Tape and reel packaging: –40°C to +80°C
最高元件温度:
+165°C (ambient + temp rise)
故障率(FIT)/平均故障间隔时间(MTBF):

性能曲线

Attenuation (Ref: 50 Ohms)

Impedance vs Frequency

原理图

schematic.png

物理特性

lpd6235d.png
dims_inches_mm.gif

卷装规格

tapereel_pl.gif

 
Parts per reel Reel dimensions (mm) Tape dimensions (mm) Orientation
7" (178 mm) 13" (330 mm) A B C D E W P Po P1 H T

part_or_aj.gif

350 1500* 178/330 60/100 13 24,4 16,4 16 12 4 2 3,68 0,3
* Special order

一般规格

核心材料:
Ferrite
重量:
420 – 480 mg
包装:
350/7″ reel; 1500/13″ reel Plastic tape: 16 mm wide, 0.3 mm thick, 12 mm pocket spacing, 3.68 mm pocket depth
Winding to Winding Isolation:
100 Vrms, one minute

焊接/清洗

湿气敏感度等级(MSL):
1 (unlimited floor life at <30°C / 85% relative humidity)
抗焊接热:
Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles
焊接之前,请参阅焊接线艺元件
推荐的取放吸嘴:
OD: 6.2 mm; ID: ≤ 3.1 mm
PCB清洗:
Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. More info.

相关产品系列