站点设定

仓库
语言设定
货币设定
资源
视频库
Cx Family Common Mode Chokes
0402CT Low Profile Chip Inductors
XAL7050 High-inductance Shielded Power Inductors
XGL4020 Ultra-low DCR Power Inductors

LPD5010 Series

Low-profile Common Mode Chokes

符合RoHS 无卤素
Coilcraft LPD5010 Series common mode chokes provide both common mode and differential mode filtering in a single miniature, low-profile device. 
  • Low-profile miniature CM choke; measures only 4.8 mm square and 0.9 mm high 
  • Common mode and differential mode filtering in a single device
  • Up to 530 MHz differential mode cutoff frequency
  • 100 Vrms, one minute winding-to-winding isolation
Refer to Designing Common Mode Filters for design guidance.
立即购买:
计数 单价
1 $1.61
250 $1.35
500 $1.12
1000 $0.93
2000 $0.84
5000 $0.76

对于大批量采购或非库存产品,点击这里请求报价

. 现货,可今天发货.
索取样品:

规格

Electrical specifications at 25°C.

零件号 1 线组数 共模
峰值阻抗 (kΩ)
截止
频率 (MHz) 2
最小
电感 (µH) 3
Irms (A) 4 DCR max (Ω) 5 隔离
电压 (Vrms) 6
LPD5010-681MR_ 2 0.88 @ 200 MHz 470 0.54 1.95 0.07 100
LPD5010-102MR_ 2 1.43 @ 160 MHz 530 0.80 1.50 0.10 100
LPD5010-152MR_ 2 2.05 @ 110 MHz 380 1.20 1.20 0.15 100
LPD5010-222MR_ 2 3.03 @ 100 MHz 260 1.76 1.10 0.20 100
LPD5010-332MR_ 2 4.60 @ 80.0 MHz 190 2.64 0.95 0.27 100
LPD5010-472MR_ 2 6.47 @ 64.0 MHz 160 3.76 0.75 0.40 100
LPD5010-562MR_ 2 7.27 @ 64.0 MHz 140 4.48 0.70 0.45 100
LPD5010-682MR_ 2 8.76 @ 54.0 MHz 150 5.44 0.60 0.53 100
LPD5010-822MR_ 2 10.97 @ 49.0 MHz 180 6.56 0.50 0.70 100
LPD5010-103MR_ 2 12.53 @ 46.0 MHz 130 8.00 0.50 0.78 100
LPD5010-153MR_ 2 18.79 @ 36.0 MHz 96.0 12.00 0.42 1.19 100
LPD5010-223MR_ 2 18.52 @ 28.0 MHz 80.0 17.60 0.35 1.58 100
LPD5010-333MR_ 2 26.33 @ 20.0 MHz 55.0 26.40 0.30 2.50 100
LPD5010-473MR_ 2 35.62 @ 18.0 MHz 43.0 37.60 0.25 3.48 100
LPD5010-683MR_ 2 48.54 @ 15.0 MHz 58.0 54.40 0.19 5.10 100
LPD5010-104MR_ 2 78.14 @ 13.0 MHz 50.0 80.00 0.15 8.00 100
LPD5010-154MR_ 2 116.80 @ 9.8 MHz 26.0 120.00 0.12 11.70 100
LPD5010-224MR_ 2 129.40 @ 7.2 MHz 28.0 176.00 0.11 15.20 100
注释
  1. When ordering, please specify termination and packaging codes: e.g. LPD5010-224MRC
  2. Frequency at which the differential mode attenuation equals 3 dB
  3. Inductance shown for each winding, measured at 100 kHz, 0.1 Vrms, 0 Adc on an Agilent/HP 4284A LCR meter or equivalent.
  4. Irms: Current that causes a 40°C temperature rise from 25°C ambient. This information is for reference only and does not represent absolute maximum ratings.
  5. DCR is for each winding, measured at 25°C. For other operating temperatures, use this DCR at Temperature calculator.
  6. Interwinding isolation (hipot) tested for one minute.

 

端子:

  • R = Matte tin over nickel over silver
  • Q = RoHS tin-silver-copper (95.5/4/0.5)(Special order, added cost)
  • P = non-RoHS tin-lead (63/37)(Special order, added cost)

包装:

  • C = 7" machine-ready reel
    EIA-481 embossed plastic tape (1000 parts per full reel).
  • B = Less than full reel
    In tape, but not machine-ready. To have a leader and trailer added ($25 charge), use code letter C instead.
  • D = 13" machine-ready reel
    EIA-481 embossed plastic tape. Factory order only, not stocked (3500 parts per full reel).
环境
环境:
符合RoHS , 无卤素
环境温度范围:
–40°C to +85°C with (40°C rise) Irms current
储存温度范围:
Component: –40°C to +125°C
Tape and reel packaging: –40°C to +80°C
最高元件温度:
+125°C (ambient + temp rise)
故障率(FIT)/平均故障间隔时间(MTBF):
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332

性能曲线

Attenuation (Ref: 50 Ohms)

Impedance vs Frequency

原理图

LPD_CM_Choke_Schematic.gif

物理特性

lpd5010d.gif

dims_inches_mm.gif

卷装规格

tapereel_pl.gif

 
Parts per reel Reel dimensions (mm) Tape dimensions (mm) Orientation
7" (178 mm) 13" (330 mm) A B C D E W P Po P1 H T part_or_aj.gif
1000 3500* 178/330 60/100 13 18,4 12,4 12 8 4 2 1,02 0,3
* Special order

一般规格

核心材料:
Ferrite
重量:
60 – 70 mg
Winding to Winding Isolation:
100 Vrms, one minute

焊接/清洗

湿气敏感度等级(MSL):
1 (unlimited floor life at <30°C / 85% relative humidity)
抗焊接热:
Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles
焊接之前,请参阅焊接线艺元件
推荐的取放吸嘴:
OD: 5 mm; ID: ≤ 2.5 mm
PCB清洗:
Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. More info.

相关产品系列