サイトの設定

倉庫
言語の設定
通貨の設定
製品
リソース
ビデオライブラリ
Cx Family Common Mode Chokes
0402CT Low Profile Chip Inductors
XAL7050 High-inductance Shielded Power Inductors
XGL4020 Ultra-low DCR Power Inductors

MSD1514-683

MSD1514-683MED

RoHS準拠 ハロゲンフリー

部品の詳細情報と仕様について

シリーズへ移動
今すぐ購入:
個数 単価
1 $4.39
175 $3.86
700 $1.74
1400 $1.36
2800 $1.17
5250 $1.08

大量のご注文または在庫のない商品については、お見積もりをご依頼ください

. 在庫あり、即日出荷可能.
サンプルを依頼:

仕様

Electrical specifications at 25°C.

フライバック用途

部品番号 1
(Hover for schematics)
インダクタンス (µH) 2
(公差: ±20%)
DCR (Ω) 3 絶縁
電圧 (V)
漏れ
インダクタンス (nH) 5
巻数比
typ max
MSD1514-683ME_ 68 0.078 0.090 500 550 1 : 1

SEPIC用途

部品番号 1
(Hover for schematics)
インダクタンス (µH) 2
(公差: ±20%)
DCR (Ω) 3 SRF typ (MHz) 4 結合係数 漏れ
インダクタンス (nH) 5
Isat (A) 6 Irms (A)
typ max 10% drop 20% drop 30% drop 両方の巻線 7 単一巻線 8
MSD1514-683ME_ 68 0.078 0.090 5.2 >0.99 550 5.1 5.7 6.2 2.2 3.2
メモ
  1. When ordering, please specify termination and packaging codes: e.g. MSD1583-105KEC
  2. Inductance shown for each winding, measured at 100 kHz, 0.1 Vrms, 0 Adc on an Agilent/HP 4284A LCR meter or equivalent. When leads are connected in parallel, inductance is the same value. When leads are connected in series, inductance is four times the value
  3. DCR is for each winding. When leads are connected in parallel, DCR is half the value. When leads are connected in series, DCR is twice the value.
  4. SRF measured using an Agilent/HP 4191A or equivalent. When leads are connected in parallel, SRF is the same value.
  5. Leakage Inductance is for L1 and is measured with L2 shorted.
  6. Isat: DC current, at which the inductance drops the specified amount from its value without current. It is the sum of the current flowing in both windings.
  7. Irms, both windings: Equal current when applied to each winding simultaneously that causes a 40°C temperature rise from 25°C ambient. This information is for reference only and does not represent absolute maximum ratings. Determine temperature rise.
  8. Irms, one winding: Current when applied to one winding that causes a 40°C temperature rise from 25°C ambient. This information is for reference only and does not represent absolute maximum ratings. Determine temperature rise.

終端処理:

  • E = Matte tin over nickel over phos bronze.
  • Q = RoHS tin-silver-copper (95.5/4/0.5). (Special order, added cost)
  • P = non-RoHS tin-lead (63/37). (Special order, added cost)

パッケージ:

  • D = 13″ machine-ready reel. EIA-481 embossed plastic tape (175 parts per full reel). Quantities less than full reel available: in tape (not machine ready) or with leader and trailer ($25 charge).
  • B = Less than full reel. In an effort to simplify our part numbering system, Coilcraft is eliminating the need for multiple packaging codes. When ordering, simply change the last letter of your part number from B to D.
環境
環境:
RoHS準拠 , ハロゲンフリー
周囲温度範囲:
–40°C to +85°C with (40°C rise) Irms current.
保管温度範囲:
Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
最大部品温度:
+125°C (ambient + temp rise).
時間内の障害(FIT)/平均障害間隔(MTBF):

性能曲線

Inductance vs Current

Inductance vs Frequency

回路図

msd1514schem.gif

物理的特徴

msd1514d-(1).gif
 

テープ&リール仕様

tapereel_pl-(25).gif

 
Parts per reel Reel dimensions (mm) Tape dimensions (mm) Orientation
13" (330 mm) A B C D E W P Po P1 H T part_or_ak-(7).gif
175 330 100 13 38,4 32,4 32 24 4 2 14.3 0,5

一般仕様

コア材料:
Ferrite
重量:
9.0 – 11.8 g
パッケージ:
175/13″ reel; Plastic tape: 32 mm wide, 0.5 mm thick, 24 mm pocket spacing, 14.3 mm pocket depth
Winding to Winding Isolation:
500 Vrms, one minute

はんだ付け/洗浄

湿度感度レベル(MSL):
1 (unlimited floor life at <30°C / 85% relative humidity)
はんだに対する耐熱性:
Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles
はんだ付けする前に、 Coilcraftコンポーネントのはんだ付けを参照してください。
PCB洗浄:
Tested with pure water or alcohol only. More info.

関連製品