サイトの設定

倉庫
言語の設定
通貨の設定
製品
リソース
ビデオライブラリ
Cx Family Common Mode Chokes
0402CT Low Profile Chip Inductors
XAL7050 High-inductance Shielded Power Inductors
XGL4020 Ultra-low DCR Power Inductors

HP1 Series

Hexa-Path Magnetics

RoHS準拠
  • Six 1 : 1 isolated windings that can be connected in series or parallel
  • Tightly coupled windings
  • 500 Vrms isolation between each winding
  • UL1446 Class F (155°C) Insulation System (UL File E83628)
  • Power range: 5 – 50 Watts as inductor and flyback transformer;
    up to 150 Watts as forward transformer
  • Frequency range up to 1 MHz

今すぐ購入:
個数 単価
1 $4.98
100 $4.52
250 $2.94
500 $2.58
1000 $2.38
2500 $2.19
5000 $1.89

大量のご注文または在庫のない商品については、お見積もりをご依頼ください

. 在庫あり、即日出荷可能.
サンプルを依頼:

仕様

Electrical specifications at 25°C.

部品番号 1 インダクタンス (µH) 2 公差 (%) DCR max (mΩ) 3 電圧ー時間
製品 (V-µs) 4
ピークエネルギー貯蔵量 (µJ) 5 Isat (A) 6 Irms (mA) 7
HP1-0059L_ 3.8 5 145 23.4 93.8 1.4 740
HP1-0076L_ 4.9 10 145 23.4 74.7 1.1 740
HP1-0102L_ 6.5 15 145 23.4 55.1 0.82 740
HP1-0190L_ 12 20 145 23.4 29.8 0.44 740
HP1-1400L_ 90 25 145 23.4 Note 8 Note 8 740
HPH1-0059L_ 8.5 5 340 35.1 107 1.0 620
HPH1-0076L_ 11 10 340 35.1 99.2 0.85 620
HPH1-0102L_ 15 15 340 35.1 60.2 0.57 620
HPH1-0190L_ 27 20 340 35.1 31.1 0.30 620
HPH1-1400L_ 202 25 340 35.1 Note 8 Note 8 620
メモ
  1. When ordering, please specify packaging code: e.g. HPH1-1400LD
  2. Inductance is per winding, measured at 100 kHz, 0.1 Vrms, 0 Adc.
  3. DCR is per winding, measured at 25°C on Cambridge Technology micro-ohmmeter or equivalent. For other operating temperatures,use this DCR at Temperature calculator.
  4. Volt-time product is for a single winding or multiple windings connected in parallel. To calculate volt-time product for windings connected in series, multiply the value specified in the table by the number of windings connected.
  5. Peak energy storage is for any combination of windings, assuming saturation current applied. See note 6 for definition of saturation current.
  6. Isat: DC current at which the inductance drops 30% typ from its value without current, based on current applied to all six windings connected in series. For applications where all windings are not connected in series, use the following equation to calculate Isat: Isat = Isat(table) × 6 ÷ number of windings in series.
  7. Irms: Current that causes a 40°C rise from 25°C ambient due to self heating, tested with continuous current flow through all windings connected in series. Application temperature rise will depend on the operating current, duty cycle, and winding connection.
  8. Part is designed exclusively for use as a forward converter transformer and was not tested for energy storage and saturation current.

終端処理:

  • L = RoHS compliant tin-silver over tin over nickel over phos bronze.
  •  = RoHS tin-silver-copper (95.5/4/0.5). (Special order, added cost)
  • S = non-RoHS tin-lead (63/37). (Special order, added cost)

パッケージ:

  • D = 13″ machine-ready reel. EIA-481 embossed plastic tape. Quantities less than full reel available: in tape (not machine ready) or with leader and trailer ($25 charge).
  • B = Less than full reel. In an effort to simplify our part numbering system, Coilcraft is eliminating the need for multiple packaging codes. When ordering, simply change the last letter of your part number from B to D.
環境
環境:
RoHS準拠
周囲温度範囲:
−40°C to +85°C with Irms current
保管温度範囲:
Component: −40°C to +125°C
Packaging tape and reel or tray: −40°C to +80°C
最大部品温度:
+125°C (Ambient + temperature rise)
時間内の障害(FIT)/平均障害間隔(MTBF):

物理的特徴

hexa-path1d.gif

dims_inches_mm.gif

テープ&リール仕様

tapereel_pl.gif
 
  Parts per reel   Reel dimensions (mm)   Tape dimensions (mm) Orientation 
  13" (330 mm)   A B C D E   W P Po P1 H T
HP1 / HPH1 500   330 100 13 30,4 24,4   24 20 4 2 6,6 0,5 part_or_c-(1).gif

一般仕様

コア材料:
Ferrite
重量:
1.4 g
パッケージ:
500 per 13" reel

はんだ付け/洗浄

湿度感度レベル(MSL):
1 (unlimited floor life at <30°C / 85% relative humidity)
はんだに対する耐熱性:
Three reflows at >217°C for 90 seconds (+260°C ±5°C for 20 – 40 seconds), allowing parts to cool to room temperature between.
はんだ付けする前に、 Coilcraftコンポーネントのはんだ付けを参照してください。
PCB洗浄:
Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. More info.

関連製品シリーズ