サイトの設定

倉庫
言語の設定
通貨の設定
製品
リソース
ビデオライブラリ
Cx Family Common Mode Chokes
0402CT Low Profile Chip Inductors
XAL7050 High-inductance Shielded Power Inductors
XGL4020 Ultra-low DCR Power Inductors

PFD3215 Series

Low-profile Common Mode Chokes

RoHS準拠 ハロゲンフリー
Our PFD3215 Series low-profile common mode chokes provide both common mode and differential-mode filtering in a single device that measures just 3.32 x 2.33 x 1.5 mm. They are ideal for use in both power line and signal line applications, providing 250 Vrms, one minute winding-to-winding isolation.
  • Low-profile miniature CM choke measures just 3.32 × 2.33 × 1.5 mm
  • Common mode and differential mode filtering in a single device
  • Ideal for use in both power line and signal line applications
  • Up to 100 MHz differential mode cutoff frequency
  • 250 Vrms, one minute winding-to-winding isolation
Refer to Designing Common Mode Filters for design guidance.

今すぐ購入:
個数 単価
1 $0.80
100 $0.72
500 $0.59
1000 $0.51
2500 $0.41
5000 $0.38

大量のご注文または在庫のない商品については、お見積もりをご依頼ください

. 在庫あり、即日出荷可能.
サンプルを依頼:

仕様

Electrical specifications at 25°C.

部品番号 1 ライン コモンモード
ピークインピーダンス (kΩ)
遮断
周波数 (MHz) 2
最小
インダクタンス (µH) 3
Irms (A) 4 DCR max (Ω) 5 絶縁
電圧 (Vrms) 6
PFD3215-391ME_ 2 1.02 @ 700 MHz 490 0.31 0.98 0.070 250
PFD3215-102ME_ 2 2.46 @ 420 MHz 240 0.80 0.85 0.123 250
PFD3215-182ME_ 2 4.24 @ 270 MHz 310 1.4 0.60 0.250 250
PFD3215-222ME_ 2 5.05 @ 220 MHz 300 1.7 0.57 0.265 250
PFD3215-332ME_ 2 6.51 @ 230 MHz 260 2.6 0.55 0.360 250
PFD3215-472ME_ 2 9.42 @ 180 MHz 190 3.7 0.51 0.450 250
PFD3215-682ME_ 2 13.06 @ 170 MHz 190 5.4 0.40 0.630 250
PFD3215-103ME_ 2 17.94 @ 130 MHz 170 8.0 0.27 1.250 250
メモ
  1. When ordering, please specify packaging code: e.g. PFD3215-103MEC
  2. Frequency at which the differential mode attenuation equals 3 dB
  3. Inductance shown for each winding, measured at 100 kHz, 0.1 Vrms, 0 Adc on an Agilent/HP 4284A LCR meter or equivalent.
  4. Irms: Current that causes a 40°C temperature rise from 25°C ambient. This information is for reference only and does not represent absolute maximum ratings.
  5. DCR is for each winding, measured at 25°C. For other operating temperatures, use this DCR at Temperature calculator.
  6. Interwinding isolation (hipot) tested for one minute.

終端処理:

  • Silver-palladium-platinum-glass frit.

パッケージ:

  • C = 7″ machine-ready reel. EIA-481 embossed plastic tape (2000 parts per full reel). Quantities less than full reel available: in tape (not machine ready) or with leader and trailer ($25 charge).
  • B = Less than full reel. In an effort to simplify our part numbering system, Coilcraft is eliminating the need for multiple packaging codes. When ordering, simply change the last letter of your part number from B to C.
  • D = 13″ machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked (7500 parts per full reel).
環境
環境:
RoHS準拠 , ハロゲンフリー
周囲温度範囲:
–40°C to +85°C with Irms current
保管温度範囲:
Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
最大部品温度:
+125°C (ambient + temp rise)
時間内の障害(FIT)/平均障害間隔(MTBF):

性能曲線

Attenuation (Ref: 50 Ohms)

Impedance vs Frequency

回路図

schematic.png

物理的特徴

pfd3215d.gif
dims_inches_mm.gif

テープ&リール仕様

tapereel_pl.gif


 
Parts per reel Reel dimensions (mm) Tape dimensions (mm) Orientation
7" (178 mm) 13" (330 mm) A B C D E W P Po P1 H T part_or_i.gif
2000 7500* 178/330 60/100 13 14,4 8,4 12 4 4 2 1,65 0,23
* Special order

一般仕様

コア材料:
Ferrite
重量:
18 – 28 mg
パッケージ:
2000/7″ reel; 7500/13″ reel Plastic tape: 12 mm wide, 0.23 mm thick, 4 mm pocket spacing, 1.65 mm pocket depth
Winding to Winding Isolation:
250 Vrms, one minute

はんだ付け/洗浄

湿度感度レベル(MSL):
1 (unlimited floor life at <30°C / 85% relative humidity)
はんだに対する耐熱性:
Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles
はんだ付けする前に、 Coilcraftコンポーネントのはんだ付けを参照してください。
PCB洗浄:
Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. More info.

関連製品シリーズ