サイトの設定

倉庫
言語の設定
通貨の設定
製品
リソース
ビデオライブラリ
Cx Family Common Mode Chokes
0402CT Low Profile Chip Inductors
XAL7050 High-inductance Shielded Power Inductors
XGL4020 Ultra-low DCR Power Inductors

LPD3015-124

RoHS準拠 ハロゲンフリー
These are new halogen-free parts, recommended for new designs. They are identical in form, fit and function to the old LPD3015 parts. Existing customers will continue to be supported. (View old data sheet here.)

部品の詳細情報と仕様について

シリーズへ移動
今すぐ購入:
個数 単価
1 $0.98
250 $0.73
500 $0.48
1000 $0.35
2000 $0.30
5000 $0.27

大量のご注文または在庫のない商品については、お見積もりをご依頼ください

. 在庫あり、即日出荷可能.
サンプルを依頼:
デザイナーズキット:
キット 価格
C463 41 (3 of each) $160.00

仕様

Electrical specifications at 25°C.

フライバック用途

部品番号 1 インダクタンス (µH) 2
(公差: ±20%)
DCR max (Ω) 3 絶縁
電圧 (V)
漏れ
インダクタンス (µH) 5
巻数比
LPD3015-124MR_ 120 9.2 100 1.8 1 : 1

SEPIC用途

部品番号 1 インダクタンス (µH) 2
(公差: ±20%)
DCR max (Ω) 3 SRF typ (MHz) 4 結合係数 漏れ
インダクタンス (µH) 5
Isat (A) 6 Irms (A)
10% drop 20% drop 30% drop 両方の巻線 7 単一巻線 8
LPD3015-124MR_ 120 9.2 9.0 0.99 1.8 0.19 0.20 0.20 0.13 0.18
メモ
  1. When ordering, please specify termination and packaging codes: e.g. LPD3015-334MRC
  2. Inductance shown for each winding, measured at 100 kHz, 0.1 Vrms, 0 Adc on an Agilent/HP 4284A LCR meter or equivalent. When leads are connected in parallel, inductance is the same value. When leads are connected in series, inductance is four times the value.
  3. DCR is for each winding. When leads are connected in parallel, DCR is half the value. When leads are connected in series, DCR is twice the value. DCR at 25°C. For other operating temperatures, use this DCR at Temperature calculator.
  4. SRF measured using an Agilent/HP 4191A or equivalent. When leads are connected in parallel, SRF is the same value.
  5. Leakage Inductance is for L1 and is measured with L2 shorted.
  6. Isat: DC current, at which the inductance drops the specified amount from its value without current. It is the sum of the current flowing in both windings.
  7. Irms, both windings: Equal current when applied to each winding simultaneously that causes a 40°C temperature rise from 25°C ambient. This information is for reference only and does not represent absolute maximum ratings. Determine temperature rise.
  8. Irms, one winding: Current when applied to one winding that causes a 40°C temperature rise from 25°C ambient. This information is for reference only and does not represent absolute maximum ratings.
    Determine temperature rise.

終端処理:

  • R = Matte tin over nickel over silver.
  • Q = RoHS tin-silver-copper (95.5/4/0.5). (Special order, added cost)
  • P = non-RoHS tin-lead (63/37). (Special order, added cost)

パッケージ:

  • C = 7" machine-ready reel
    EIA-481 embossed plastic tape 1000 parts per full reel).
  • B = Less than full reel
    In tape, but not machine-ready. To have a leader and trailer added ($25 charge), use code letter C instead.
  • D = 13" machine-ready reel
    EIA-481 embossed plastic tape. Factory order only, not stocked (3500 parts per full reel).
環境
環境:
RoHS準拠 , ハロゲンフリー
周囲温度範囲:
–40°C to +85°C with (40°C rise) Irms current
保管温度範囲:
Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
最大部品温度:
+125°C (ambient + temperature rise)
時間内の障害(FIT)/平均障害間隔(MTBF):
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332

性能曲線

Inductance vs. Current

Inductance vs. Frequency

回路図

lpd3015schem.giflpd3015s.gif

物理的特徴

lpd3015d.gif
dims_inches_mm.gif

テープ&リール仕様

tapereel_pl.gif
Parts per reel Reel dimensions (mm) Tape dimensions (mm) Orientation
7" (178 mm) 13" (330 mm) A B C D E W P Po P1 H T part_or_aj.gif
1000 3500* 178/330 60/100 13 18,4 12,4 12 8 4 2 1,65 0,26
* Special order
 

一般仕様

コア材料:
Ferrite
重量:
45 - 52 mg
パッケージ:
1000/7″ reel; 3500/13″ reel Plastic tape: 12 mm wide, 0.26 mm thick, 8 mm pocket spacing, 1.65 mm pocket depth
Winding to Winding Isolation:
100 Vrms, one minute

はんだ付け/洗浄

湿度感度レベル(MSL):
1 (unlimited floor life at <30°C / 85% relative humidity)
はんだに対する耐熱性:
Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles
はんだ付けする前に、 Coilcraftコンポーネントのはんだ付けを参照してください。
推奨ピック&プレースノズル:
OD: 3 mm; ID: < 1.5 mm
PCB洗浄:
Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. More info.

関連製品