サイトの設定

倉庫
言語の設定
通貨の設定
製品
リソース
ビデオライブラリ
Cx Family Common Mode Chokes
0402CT Low Profile Chip Inductors
XAL7050 High-inductance Shielded Power Inductors
XGL4020 Ultra-low DCR Power Inductors

CM1394 Series

IEEE1394 Common Mode Choke

RoHS準拠
Our CM1394 Series common mode choke was designed for IEEE1394 and other twisted-pair interfaces. It provides common mode and differential mode filtering in a single device with more than 21 dB attenuation at 400 MHz and is less expensive than hand-wound toroid designs.
  • Designed for IEEE1394 and other twisted-pair interfaces
  • Common mode and differential mode filtering in a single device
  • More than 21 dB attenuation at 400 MHz
  • Less expensive than hand-wound toroid designs
  • Defense Supply Center CID A-A-59744
Refer to Designing Common Mode Filters for design guidance.
今すぐ購入:
個数 単価
1 $2.50
300 $1.85
600 $1.37
1200 $1.02
2400 $0.75
4800 $0.58

大量のご注文または在庫のない商品については、お見積もりをご依頼ください

. 在庫あり、即日出荷可能.
サンプルを依頼:

仕様

Electrical specifications at 25°C.

部品番号 1 ライン コモンモード
ピークインピーダンス (kΩ)
遮断
周波数 (MHz) 2
コモンモード
減衰タイプ (dB)
最小
インダクタンス (µH) 3
Irms (A) 4 DCR max (Ω) 5 絶縁
電圧 (Vrms) 6
100 MHz 500 MHz
CM1394L_ 2 0.813 @ 660 MHz 1200 11.1 22.7 0.22 1.5 0.105 50
メモ
  1. When ordering, please specify packaging code: e.g. CM1394LC
  2. Frequency at which the differential mode attenuation equals 3 dB
  3. Inductance measured at 100 MHz.
  4. Irms: Current per winding that causes a 20°C temperature rise from 25°C ambient. This information is for reference only and does not represent absolute maximum ratings.
  5. DCR is specified per winding at 25°C. For other operating temperatures, use this DCR at Temperature calculator.
  6. Winding to winding isolation (hipot) tested for one minute.

終端処理:

  • RoHS compliant gold over nickel over moly-manganese.

パッケージ:

  • C = 7" machine-ready reel
    EIA-481 embossed plastic tape (600 parts per full reel).
  • B = Less than full reel
    In tape but not machine-ready. To have a leader and trailer added ($25 charge), use code letter C instead.
  • 13" reel, machine-ready 
    EIA-481 embossed plastic tape. Factory order only, not stocked (2200 parts per full reel).
環境
環境:
RoHS準拠
周囲温度範囲:
–40°C to +85°C with Irms current
保管温度範囲:
Component: –40°C to +100°C.
Tape and reel packaging: –40°C to +80°C
最大部品温度:
+100°C (ambient + temp rise)
時間内の障害(FIT)/平均障害間隔(MTBF):
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332

性能曲線

Attenuation (Ref: 50 Ohms)

Impedance vs Frequency

回路図

m2022sch.gif

物理的特徴

m2022as.gif
 
A max B max C max D ref E ref F ref G min H
0.231 0.196 0.150 0.107 0.100 0.178 0.04 0.03
5,87 4,98 3,81 2,72 2,54 4,52 1,02 0,76


1812pad.gif              m2022lnd.gif

テープ&リール仕様

tapereel_pl.gif


 
Parts per reel Reel dimensions (mm) Tape dimensions (mm) Orientation
7" (178 mm) 13" (330 mm) A B C D E W P Po P1 H T part_or_i.gif
600 2200* 178/330 60/100 13 18,4 12,4 12 8 4 2 3,9 0,25
* Special order

一般仕様

コア材料:
Ferrite
重量:
30 mg

はんだ付け/洗浄

湿度感度レベル(MSL):
1 (unlimited floor life at <30°C / 85% relative humidity)
はんだに対する耐熱性:
Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles
はんだ付けする前に、 Coilcraftコンポーネントのはんだ付けを参照してください。
PCB洗浄:
Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. More info.

関連製品シリーズ