사이트 설정

창고
언어 설정
통화 설정
리소스
비디오 라이브러리
Cx Family Common Mode Chokes
0402CT Low Profile Chip Inductors
XAL7050 High-inductance Shielded Power Inductors
XGL4020 Ultra-low DCR Power Inductors

LPD5010 Series

Low-profile Common Mode Chokes

RoHS 준수 할로겐 프리
Coilcraft LPD5010 Series common mode chokes provide both common mode and differential mode filtering in a single miniature, low-profile device. 
  • Low-profile miniature CM choke; measures only 4.8 mm square and 0.9 mm high 
  • Common mode and differential mode filtering in a single device
  • Up to 530 MHz differential mode cutoff frequency
  • 100 Vrms, one minute winding-to-winding isolation
Refer to Designing Common Mode Filters for design guidance.
지금 구매:
개수 단품 가격
1 $1.61
250 $1.45
500 $1.20
1000 $1.00
2000 $0.90
5000 $0.82

대량 또는 비재고 품목의 경우, 견적서를 요청하십시오.

. 재고 보유 중, 당일 발송 가능.
샘플 신청:

사양

Electrical specifications at 25°C.

부품 번호 1 라인 공통 모드
피크 임피던스 (kΩ)
차단
주파수 (MHz) 2
인덕턴스
최소 (µH) 3
Irms (A) 4 DCR max (Ω) 5 절연
전압 (Vrms) 6
LPD5010-681MR_ 2 0.88 @ 200 MHz 470 0.54 1.95 0.07 100
LPD5010-102MR_ 2 1.43 @ 160 MHz 530 0.80 1.50 0.10 100
LPD5010-152MR_ 2 2.05 @ 110 MHz 380 1.20 1.20 0.15 100
LPD5010-222MR_ 2 3.03 @ 100 MHz 260 1.76 1.10 0.20 100
LPD5010-332MR_ 2 4.60 @ 80.0 MHz 190 2.64 0.95 0.27 100
LPD5010-472MR_ 2 6.47 @ 64.0 MHz 160 3.76 0.75 0.40 100
LPD5010-562MR_ 2 7.27 @ 64.0 MHz 140 4.48 0.70 0.45 100
LPD5010-682MR_ 2 8.76 @ 54.0 MHz 150 5.44 0.60 0.53 100
LPD5010-822MR_ 2 10.97 @ 49.0 MHz 180 6.56 0.50 0.70 100
LPD5010-103MR_ 2 12.53 @ 46.0 MHz 130 8.00 0.50 0.78 100
LPD5010-153MR_ 2 18.79 @ 36.0 MHz 96.0 12.00 0.42 1.19 100
LPD5010-223MR_ 2 18.52 @ 28.0 MHz 80.0 17.60 0.35 1.58 100
LPD5010-333MR_ 2 26.33 @ 20.0 MHz 55.0 26.40 0.30 2.50 100
LPD5010-473MR_ 2 35.62 @ 18.0 MHz 43.0 37.60 0.25 3.48 100
LPD5010-683MR_ 2 48.54 @ 15.0 MHz 58.0 54.40 0.19 5.10 100
LPD5010-104MR_ 2 78.14 @ 13.0 MHz 50.0 80.00 0.15 8.00 100
LPD5010-154MR_ 2 116.80 @ 9.8 MHz 26.0 120.00 0.12 11.70 100
LPD5010-224MR_ 2 129.40 @ 7.2 MHz 28.0 176.00 0.11 15.20 100
메모
  1. When ordering, please specify termination and packaging codes: e.g. LPD5010-224MRC
  2. Frequency at which the differential mode attenuation equals 3 dB
  3. Inductance shown for each winding, measured at 100 kHz, 0.1 Vrms, 0 Adc on an Agilent/HP 4284A LCR meter or equivalent.
  4. Irms: Current that causes a 40°C temperature rise from 25°C ambient. This information is for reference only and does not represent absolute maximum ratings.
  5. DCR is for each winding, measured at 25°C. For other operating temperatures, use this DCR at Temperature calculator.
  6. Interwinding isolation (hipot) tested for one minute.

 

종단 처리:

  • R = Matte tin over nickel over silver
  • Q = RoHS tin-silver-copper (95.5/4/0.5)(Special order, added cost)
  • P = non-RoHS tin-lead (63/37)(Special order, added cost)

패키지:

  • C = 7" machine-ready reel
    EIA-481 embossed plastic tape (1000 parts per full reel).
  • B = Less than full reel
    In tape, but not machine-ready. To have a leader and trailer added ($25 charge), use code letter C instead.
  • D = 13" machine-ready reel
    EIA-481 embossed plastic tape. Factory order only, not stocked (3500 parts per full reel).
환경
환경:
RoHS 준수 , 할로겐 프리
주변 온도 범위:
–40°C to +85°C with (40°C rise) Irms current
보관 온도 범위:
Component: –40°C to +125°C
Tape and reel packaging: –40°C to +80°C
최고 부품 온도:
+125°C (ambient + temp rise)
고장 비율(FIT) / 평균 고장률(MTBF):

성능 곡선

Attenuation (Ref: 50 Ohms)

Impedance vs Frequency

회로도

LPD_CM_Choke_Schematic.gif

물리적 특성

lpd5010d.gif

dims_inches_mm.gif

테이프 및 릴 사양

tapereel_pl.gif

 
Parts per reel Reel dimensions (mm) Tape dimensions (mm) Orientation
7" (178 mm) 13" (330 mm) A B C D E W P Po P1 H T part_or_aj.gif
1000 3500* 178/330 60/100 13 18,4 12,4 12 8 4 2 1,02 0,3
* Special order

일반 사양

코어 소재:
Ferrite
중량:
60 – 70 mg
Winding to Winding Isolation:
100 Vrms, one minute

납땜/세척

수분 민감도(MSL):
1 (unlimited floor life at <30°C / 85% relative humidity)
납땜 열 내성:
Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles
납땜 전에 Coilcraft 부품의 납땜을 참조하십시오.
권장 픽앤플레이스 노즐:
OD: 5 mm; ID: ≤ 2.5 mm
PCB 세척:
Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. More info.

관련 제품 시리즈

관련 제품군