사이트 설정

창고
언어 설정
통화 설정
리소스
비디오 라이브러리
Cx Family Common Mode Chokes
0402CT Low Profile Chip Inductors
XAL7050 High-inductance Shielded Power Inductors
XGL4020 Ultra-low DCR Power Inductors

LPD5030-222

LPD5030-222MRC

RoHS 준수 할로겐 프리 AEC-Q flag
This is a new, improved LPD5030 version recommended for new designs. Only the termination material and part number have changed. The previous version is available only to current customers.

부품에 대한 추가 정보 및 사양.

시리즈로 이동
지금 구매:
개수 단품 가격
1 $1.14
375 $0.95
750 $0.65
1500 $0.55
3000 $0.45
6000 $0.42

대량 또는 비재고 품목의 경우, 견적서를 요청하십시오.

. 재고 보유 중, 당일 발송 가능.
샘플 신청:
설계자용 키트:
키트 가격
C463 41 (3 of each) $160.00

사양

Electrical specifications at 25°C.

플라이백 용도

부품 번호 1
(Hover for schematics)
인덕턴스 (µH) 2
(허용 오차: ±20%)
DCR max (Ω) 3 절연
전압 (V)
누설
인덕턴스 (nH) 5
권수비
LPD5030-222MR_ 2.2 0.067 100 100 1 : 1

SEPIC 용도

부품 번호 1
(Hover for schematics)
인덕턴스 (µH) 2
(허용 오차: ±20%)
DCR max (Ω) 3 SRF typ (MHz) 4 결합 계수 누설
인덕턴스 (nH) 5
Isat (A) 6 Irms (A)
10% drop 20% drop 30% drop 양측 권선 7 단일 권선 8
LPD5030-222MR_ 2.2 0.067 87.0 0.98 100 2.8 3.0 3.1 2.0 2.8
메모
  1. When ordering, please specify termination and packaging codes: e.g. LPD5030-105MRC
  2. Inductance shown for each winding, measured at 100 kHz, 0.1 Vrms, 0 Adc on an Agilent/HP 4284A LCR meter or equivalent. When leads are connected in parallel, inductance is the same value. When leads are connected in series, inductance is four times the value
  3. DCR is for each winding. When leads are connected in parallel, DCR is half the value. When leads are connected in series, DCR is twice the value. DCR at 25°C. For other operating temperatures, use this DCR at Temperature calculator.
  4. SRF measured using an Agilent/HP 4191A or equivalent. When leads are connected in parallel, SRF is the same value.
  5. Leakage inductance is for L1 and is measured with L2 shorted.
  6. Isat: DC current, at which the inductance drops the specified amount from its value without current. It is the sum of the current flowing in both windings.
  7. Irms, both windings: Equal current when applied to each winding simultaneously that causes a 40°C temperature rise from 25°C ambient. This information is for reference only and does not represent absolute maximum ratings. Determine temperature rise.
  8. Irms, one winding: Current when applied to one winding that causes a 40°C temperature rise from 25°C ambient. This information is for reference only and does not represent absolute maximum ratings. Determine temperature rise.

종단 처리:

  • R = Matte tin over nickel over silver
  • Q = RoHS tin-silver-copper (95.5/4/0.5). (Special order, added cost)
  • P = non-RoHS tin-lead (63/37). (Special order, added cost)

패키지:

  • C = 7″ machine-ready reel. EIA-481 embossed plastic tape (750 parts per full reel). Quantities less than full reel available: in tape (not machine ready) or with leader and trailer ($25 charge).
  • B = Less than full reel. In an effort to simplify our part numbering system, Coilcraft is eliminating the need for multiple packaging codes. When ordering, simply change the last letter of your part number from B to C.
  • D = 13″ machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked (2500 parts per full reel).
환경
환경:
RoHS 준수 , 할로겐 프리
주변 온도 범위:
–40°C to +85°C with (40°C rise) Irms current.
보관 온도 범위:
Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
최고 부품 온도:
+125°C (ambient + temperature rise).
고장 비율(FIT) / 평균 고장률(MTBF):

성능 곡선

Inductance vs. Current

Inductance vs. Frequency

회로도

lpd5030schem.gif

물리적 특성

lpd5030d.gif     lpd4012s.gif

dims_inches_mm.gif

테이프 및 릴 사양

tapereel_pl.gif


 
Parts per reel Reel dimensions (mm) Tape dimensions (mm) Orientation
7" (178 mm) 13" (330 mm) A B C D E W P Po P1 H T part_or_aj.gif
750 2500* 178/330 60/100 13 18,4 12,4 12 8 4 2 3,1 0,32
* Special order
 

일반 사양

코어 소재:
Ferrite
중량:
210 – 225 mg
패키지:
750/7″ reel; 2500/13″ reel Plastic tape: 12 mm wide, 0.32 mm thick, 8 mm pocket spacing, 3.1 mm pocket depth
Winding to Winding Isolation:
100 Vrms, one minute

납땜/세척

수분 민감도(MSL):
1 (unlimited floor life at <30°C / 85% relative humidity)
납땜 열 내성:
Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles
납땜 전에 Coilcraft 부품의 납땜을 참조하십시오.
권장 픽앤플레이스 노즐:
OD: 5 mm; ID: < 2.5 mm
PCB 세척:
Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. More info.

관련 제품