사이트 설정

창고
언어 설정
통화 설정
리소스
비디오 라이브러리
Cx Family Common Mode Chokes
0402CT Low Profile Chip Inductors
XAL7050 High-inductance Shielded Power Inductors
XGL4020 Ultra-low DCR Power Inductors

FCT1-120D3SL

FCT1-120D3SLD

RoHS 준수

부품에 대한 추가 정보 및 사양.

시리즈로 이동
지금 구매:
개수 단품 가격
1 $6.81
175 $5.46
700 $3.28
1400 $2.55
2800 $2.19
5000 $2.01

대량 또는 비재고 품목의 경우, 견적서를 요청하십시오.

. 재고 보유 중, 당일 발송 가능.
샘플 신청:

사양

Electrical specifications at 25°C.

부품 번호 1
(Hover for schematics)
전력 (W) 입력 전압 (V) 인덕턴스
최소 (µH) 2
DCR max (mΩ) 3 누설
인덕턴스
최대 (µH) 4
권수비 5 주파수 (kHz) 절연
전압 (Vrms) 6
이차
출력 (V, A)
Pri Sec Sync Bias Pri : Sec : Sync : Bias
FCT1-120D3SL_ 30 36 72 72.9 27.5 28.5 160.0 250.0 0.175 1 : 1 : 0.56 : 1 250 1500 12 V , 2.5 A
메모
  1. When ordering, please specify packaging code: e.g. FCT1-240D3SLD
  2. Inductance is measured at 250 kHz, 0.2 Vrms, 0 Adc.
  3. DCR for the primary and secondary is with the windings connected in parallel.
  4. Leakage inductance is for the primary windings with the secondary windings shorted.
  5. Turns ratio is with the primary windings and the secondary windings connected in parallel.
  6. 1500 Vrms winding to winding isolation.

종단 처리:

  • L = RoHS tin-silver over tin over nickel over phos bronze.
  • T = RoHS tin-silver-copper (95.5/4/0.5). (Special order, added cost)
  • S = non-RoHS tin-lead (63/37). (Special order, added cost)

패키지:

  • D = 13" machine-ready reel
    EIA 481 embossed plastic tape (175 parts per full reel)
  • B = Less than full reel
    In tape, but not machine-ready. To have a leader and trailer added ($25 charge), use code letter D instead.
환경
환경:
RoHS 준수
주변 온도 범위:
–40°C to +125°C
보관 온도 범위:
Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
고장 비율(FIT) / 평균 고장률(MTBF):

회로도

fct1xxd3slschematic.gif

The primary windings and the secondary windings are to be
connected in parallel on the PC board.
Transformer Recommended
output inductor
FCT1-33D3SL SER2013-472
FCT1-50D3SL SER1360-103
FCT1-120D3SL MSS1278-563
FCT1-195D3SL MSS1278-154
FCT1-240D3SL MSS1278-224

These inductors are recommended for 30% ripple current. Ripple less than 30% may require the use of physically larger inductors. Allowing higher ripple current to make use of smaller inductors may create a risk of discontinuous output current.

물리적 특성

fct1xxd3sldimensions.gif

dims_inches_mm.gif

테이프 및 릴 사양

tapereel_pl.gif

 
Parts per reel Reel dimensions (mm) Tape dimensions (mm) Orientation
13" (330 mm) A B C D E W P Po P1 H T FCT1-xxD3SLorientation.gif
175 330 100 13 50,4 44,4 44 32 4 2 12,0 0,4

일반 사양

코어 소재:
Ferrite
중량:
10.1 – 10.7 g
패키지:
175 per 13″ reel Plastic tape: 44 mm wide, 0.4 mm thick, 32 mm pocket spacing, 12.0 mm pocket depth

납땜/세척

수분 민감도(MSL):
1 (unlimited floor life at <30°C / 85% relative humidity
납땜 열 내성:
Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles
납땜 전에 Coilcraft 부품의 납땜을 참조하십시오.
PCB 세척:
Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. More Info.

관련 제품